Jump to content
  • Announcements

    • Rahul Ponginan

      Please click here for a short but important announcement   03/26/17

      Dear Users Our Commercial and Academic users around the world can use these same forums here as before i.e. the Altair Support Forum , Commercial users from India with solver queries can go to the Solver Forum for India Commercial Users , Academic Users from India and AOC India Participants are requested to go to the Forum for India Academic Users and AOC India Participants , We will be tending to all queries in all the forums promptly as before, thank you for your understanding. 
    • Rahul Ponginan

      ユーザーフォーラムについて   10/22/17

      アルテアエンジニアリングでは、弊社製品や技術について、ユーザー様同士がオンラインで情報交換できる場所を提供しています。 日常業務の中で起こるさまざまな問題の解決や、他ユーザー様との技術交流を図るための場として、お客様の環境に合わせてご活用ください。

zyuce

Members
  • Content count

    16
  • Joined

  • Last visited

About zyuce

  • Rank
    Beginner

Profile Information

  • Country
    Turkey
  • Are you University user?
    No
  1. Tinh and George, thank you for your support.
  2. Hello Tinh! I have checked the reference guide but I could not find a command as; " hm_holedetectioninit hm_holedetectionsetentities elems 1 hm_holedetectionsetholeparams hole_shape=31 hm_holedetectionfindholes 1 " Can you share if you have a document about these commands?
  3. Hello All, I am trying to create rigid elems for a spesific shell component with holes on it. In documentation I have discovered *finholesinit tcl command. However I can not obtain line number also I can not define center of circle using tcl automatically. How can I achieve this problem?
  4. Hi Merula, Tank you for support. I have developed following code based on your suggestions. Finally it works . Hi Tinh, Thank you for your help. ###################################################################### *clearmark nodes all *createmark nodes 1 "by sphere" -341.255 -75.946 6.482 0.25 inside 1 all 0 *appendmark nodes 1 "by sphere" -341.252 76.398 -3.898 0.25 inside 1 all 0 *appendmark nodes 1 "by face" set nrbl [hm_marklength node 1] set dofl [lrepeat $nrbl 123456] set wgh1 [lrepeat $nrbl 1] eval *createarray $nrbl $dofl eval *createdoublearray $nrbl $wgh1 *createnode -341.761 9.994e-02 1.549 0 0 0 *createmark nodes 2 "by sphere" -341.761 9.994e-02 1.549 0.2 inside 1 all 0 eval *rbe3 1 1 $nrbl 1 $nrbl [hm_getmark nodes 2] 123456 1 *nodecleartempmark ###################################################################
  5. Hello all, I am trying to create rbe3 element with 1.0 weight to independent nodes , however, following code generates 0.0 weight for independent nodes. my tcl code is ; ################################################################## *createmark nodes 1 "by sphere" -341.255 -75.946 6.482 0.25 inside 1 all 0 *appendmark nodes 1 "by face" set rbl [hm_getmark nodes 1] set nrbl [llength $rbl] for {set i 0} {$i < $nrbl} {incr i 1} { lappend dofl 123456 } *createarray $nrbl [puts $dofl] for {set i 0} {$i < $nrbl} {incr i 1} { lappend wgh1 1.500000 } *createdoublearray $nrbl [puts $wgh1] *createnode -341.761 9.994e-02 1.549 0 0 0 *createmark nodes 2 "by sphere" -341.761 9.994e-02 1.549 0.2 inside 1 all 0 *rbe3 1 1 $nrbl 1 $nrbl [hm_getmark nodes 2] 123456 0 ######################################################################## At the end of the day, I want to generate following RBE3;
  6. scripting in simlab

    Dear Alessio, Thank you for your support. I tryed to find SL 2017 deocument in Altair connect but, there is tutorials for SL 14 and older versions. In other words, I could not find the tutorial that you suggested. Can you describe how to find that document?
  7. Virtual Fluid Mass Error

    Hello All, I am tring to utilize Virtual Fluid Mass method in order to calculate natural frequencies of fuel tank. However, aacording to results, dry modes are consistent with measured acceleration data, but, wet modes are completely different than test data. Three wet modes, three dry modes are calculated, but wet mode shapes are completely same. Just natural frequency values are different. According to test data, mode shapes of first three mode are completely different. Do you have any idea to sole this problem? Pictures shown below explains my step card. **ELIST 666 is created, because both sides of baffle plates inside of the fuel tank contact with fluid. **ELIST 555 is created, beacuse inner side of the fuel tank contact with fluid. **During shaker tests water is used in order to represent fuel in the tank. Hence, density of water is considered in MFLUID command.
  8. scripting in simlab

    Hello All, Are there any scripting language that can be utilized in simlab, in order to automate the meshing process? Besides, does simlab creates a command file such as .cmf file like hypermesh?
  9. Hello all, Is there a way to find lines of holes on a midsurface? Based on my DOE, locations of bolt holes are always changing, so I want to select holes usign tcl code.
  10. I found the mistake; "abaqus\abaqus" need to be changed to abaqus/abaqus
  11. Hello all, I copied following codes from .cmf file. However it does not work. Do you have any idea about this script? ## *feinputpreserveincludefiles *createstringarray 2 "Abaqus " "Standard3D " *feinputwithdata2 "#abaqus\abaqus" "C:/Users/zyuce/Desktop/TCL/sorhan/new/code/EU6_with_omega.inp" 0 0 0 0 0 1 2 1 0 ##
  12. Dear Tinh, Thank you for your reply. I have tryed your suggestion but I still have problem on selecting desired surfaces. As illustarated in the picture below; Coordinated of center nodes is wrtten in "hm_measureshortestdistance2" command as, hm_measureshortestdistance1 6310.316 -437 1212.594 surfaces 1 0 0 However, in order to check if selection of washer surface is completed hm_getmark surfaces 1 is written. But nothing appeared on the screen. Unfortunately, surface is not selected. Do you have any suggestion to achieve this problem?
  13. Hello all, Is it possible to select some surfaces by defining their coordinates or sth else in tcl script? Note: I can make it by createnarkpanel command but i dont want to select surfaces in GUI. So, I want to learn if I can handle it without mauel selection by mouse.
  14. Hello all, Is tahat possible to run a tcl script without opening Hypermesh. Such as just using command window similar to "Abaqus command".
×